#Electrical Switchboard Drawing Software how to
#Electrical Switchboard Drawing Software code

Chiller, Centrifugal, water cooled, over 100 tons: CHL-CW2.

Chiller, Absorption unit, up to 500 tons: CHL-A1.

Chiller, Absorption unit, 500 to 5000 tons: CHL-A2.

Building Automation System, Terminal End Devices: BAS-03.

Building Automation System, Pnuematic: BAS-02.

Building Automation System, DDC: BAS-01.

Boiler, Steam, Oil/Gas/Comb, up to 120 MBH: BLR-ST1.

Boiler, Steam, Oil/Gas/Comb, over 1000 MBH: BLR-ST4.

Boiler, Steam, Oil/Gas/Comb, 500 to 1000 MBH: BLR-ST3.

Boiler, Hot Water, Oil/Gas/Comb, up to 120 MBH: BLR-HW1.

Boiler, Hot Water, Oil/Gas/Comb, over 1000 MBH: BLR-HW4.

Boiler, Hot Water, Oil/Gas/Comb, 500 to 1000 MBH: BLR-HW3.

Boiler, Hot Water, Oil/Gas/Comb, 120 to 500 MBH: BLR-HW2.

Air Handling Unit, Computer Room: AHU-04.

Air Handling Unit, 3 ton thru 24 ton: AHU-01.

Air Handling Unit, 25 ton thru 50 ton: AHU-02.

Non-standard names may only be used when standard names, such as floor or area, do not describe the contents of the folder or file.

Non-standard names must meet the general naming requirements.

The use of non-standard names for the purposes of logically organizing the data is allowed.

All naming within the point cloud data is to follow the General Naming Guidelines.

If previous data for the same site exists and conforms to the standard, the naming convention established by that data is to be followed for all new data.

Naming will be consistent across the project, even when multiple capture firms are present.

For example, if the building or site name is contained in the folder name of the data's location, it should not be repeated in the name of a single scan.

Hierarchical divisions are not to be repeated.

The hierarchical divisions are to be: Building > Floor > Area > Room.

For example interior building data should be named 'Area # - Room # - #' where the last two digits are sequential numbers to support multiple scans of the same room.

The naming convention will be hierarchical based on established divisions of the site.

The established naming convention will be followed by all project participants.

A naming convention will be established as part of the BEP.

#Electrical Switchboard Drawing Software how to

The producer of the 3D imaging data is highly encouraged to engage the GSA BIM Manager in a discussion of how to apply the naming standard to the specific software being used to process the scans. Given the diverse nature of 3D Imaging software, a traditional naming standard cannot be developed. See the 3D Imaging standard for additional information on the capture and use of 3D image data on GSA projects. On most projects, this data will come from 3D laser scanning.

Telephone, network, voice, data, alarm, nurse call, security, CCTV, PA, clockģD Imaging data is considered any non-model based 3D data. Mist collection, dust collection, exhaust stacksĬontrols, relays, instrumentation and measurement devices Protection, termination and removal addedĭomestic water, sanitary and storm drainage fixturesĭomestic water, sanitary and storm drainage pipe, fixtures and equipment (unless split to separate files) Kitchen, bar, service, storage and processingįire extinguishing system and equipment (Mechanical) Gymnasium, exercise, aquatic and recreational Mainlines, valves, controller, pumps, etc.Ĭolumn grid lines and bubbles (MODEL FILE ONLY) Protection and removal of existing landscaping Water, sanitary sewer, storm sewer, power, and communications Toxic chemicals handling, removal or storageĭimensions and coordinates for aboveground site featuresĮxcavation, grading, roads and parking lots Phasing, schedules, staging areas, haul routesĪsbestos abatement, identification or containment

#Electrical Switchboard Drawing Software code

NCS Compliant Discipline Codes CategoryĬover sheet, list of sheets and symbols, code summary, orientation maps See Data Submittal Standards and the Folder Structure Template for additional information on the approved folder structure. Files must be named correctly, and be properly stored within the approved folder structure.